Class CylindricalGearMicroGeometryBase
Inheritance
System.Object
System.MarshalByRefObject
SMT.MastaAPIUtility.MarshalByRefObjectPermanent
CylindricalGearMicroGeometryBase
Inherited Members
APIBase.callPartialMethod<T>(String, (T1, T2)<Type, Object>, (T1, T2)<Type, Object>, (T1, T2)<Type, Object>, T)
SMT.MastaAPIUtility.MarshalByRefObjectPermanent.InitializeLifetimeService()
Assembly: SMT.MastaAPI.13.0.dll
Syntax
public abstract class CylindricalGearMicroGeometryBase : GearImplementationDetail, IEquatable<APIBase>
Properties
AdjustMicroGeometryForAnalysisWhenIncludingPitchErrors
Declaration
public Overridable<bool> AdjustMicroGeometryForAnalysisWhenIncludingPitchErrors { get; set; }
Property Value
CommonMicroGeometriesOfFlanks
Declaration
public ReadOnlyCollection<CylindricalGearCommonFlankMicroGeometry> CommonMicroGeometriesOfFlanks { get; }
Property Value
CommonMicroGeometryOfLeftFlank
Declaration
public CylindricalGearCommonFlankMicroGeometry CommonMicroGeometryOfLeftFlank { get; }
Property Value
CommonMicroGeometryOfRightFlank
Declaration
public CylindricalGearCommonFlankMicroGeometry CommonMicroGeometryOfRightFlank { get; }
Property Value
CylindricalGear
Declaration
public CylindricalGearDesign CylindricalGear { get; }
Property Value
Declaration
public SimpleChartDefinition LeadFormChart { get; }
Property Value
LeadSlopeChart
Declaration
public SimpleChartDefinition LeadSlopeChart { get; }
Property Value
LeadTotalChart
Declaration
public SimpleChartDefinition LeadTotalChart { get; }
Property Value
LeadTotalNominalChart
Declaration
public SimpleChartDefinition LeadTotalNominalChart { get; }
Property Value
ProfileControlPoint
Used in the Tolerances Tab. Start of profile evaluation diameter. It is the specified diameter beyond which the actual tooth profile is required to conform to the specified design. The designer may select the profile control diameter to be anywhere between the root form diameter and the start of active profile diameter.
Declaration
public CylindricalGearProfileMeasurement ProfileControlPoint { get; }
Property Value
ProfileControlPointIsUserSpecified
If this is not selected, the Lowest SAP Diameter is used. Used in the Tolerances Tab. Start of profile evaluation diameter. It is the specified diameter beyond which the actual tooth profile is required to conform to the specified design. The designer may select the profile control diameter to be anywhere between the root form diameter and the start of active profile diameter.
Declaration
public bool ProfileControlPointIsUserSpecified { get; set; }
Property Value
| Type |
Description |
| System.Boolean |
|
Declaration
public SimpleChartDefinition ProfileForm10PercentChart { get; }
Property Value
Declaration
public SimpleChartDefinition ProfileForm50PercentChart { get; }
Property Value
Declaration
public SimpleChartDefinition ProfileForm90PercentChart { get; }
Property Value
Declaration
public SimpleChartDefinition ProfileFormChart { get; }
Property Value
ProfileTotalChart
Declaration
public SimpleChartDefinition ProfileTotalChart { get; }
Property Value
ProfileTotalNominalChart
Declaration
public SimpleChartDefinition ProfileTotalNominalChart { get; }
Property Value
ToothMicroGeometries
Declaration
public ReadOnlyCollection<CylindricalGearToothMicroGeometry> ToothMicroGeometries { get; }
Property Value
UseSameMicroGeometryOnBothFlanks
If using the same micro geometry on both flanks the values for the left flank only are input and reported. Micro geometry on the right flank is then considered equivalent to the left. Linear lead relief on the right flank is such that the helix angle change is the same as on the left flank. This option is read-only when any of the flank micro geometries are defined using measured map data.
Declaration
public bool UseSameMicroGeometryOnBothFlanks { get; set; }
Property Value
| Type |
Description |
| System.Boolean |
|
Implements
System.IEquatable<T>
Extension Methods